panasonic to no. date matsushita electronic components co.,ltd kadoma, osaka, japan issued check 3rd apr. '04 data sheet egsm900 rx saw filter a .tsunekawa k ,nishimur a zgsm-040403m-01 a pplication : rx filter for egsm900 center frequency : 942.5mhz size : 2.0x1.4mm, 5pin-layout impedance : 50-50ohms unbalance-unbalance part no. : EFCH942MTCD1 erda2 t y pe no. circuit components business unit
2004.1.6 egsm900 rx saw filter ----- unbalanced input and unbalanced output ----- part no. : design no. : t942cl1 parameter frequency your request our specification unit min. typ. max. min. typ. max. passband 925 ... 960 925 ... 960 mhz insertion loss 925 ... 960mhz 1.7 2.4 db ripple in passband 925 ... 960mhz 0.6 1.5 db attenuation att1 dc ... 880mhz 30 60 db att2 880 ... 905mhz 23 32 db att3 905 ... 915mhz 18 21 db att4 980 ... 1500mhz 26 32 db att5 1500 ... 3000mhz 30 46 db att6 3000 ... 6000mhz 20 29 db vswr input 925 ... 960mhz 1.5 2.0 output 925 ... 960mhz 1.5 2.0 input impedance (single ended) 50 ohm output impedance(single ended) 50 ohm maximum drive level 13 dbm operating temperature -30 +85 deg. c storage temperature -40 +85 deg. c panasonic
2004.1.6 egsm900 rx saw filter ----- unbalanced input and unbalanced output ----- part no. : design no. : t942cl1 panasonic
2004.1.6 egsm900 rx saw filter ----- unbalanced input and unbalanced output ----- part no. : design no. : t942cl1 panasonic
do not scale drawing revisions indicated by ? all dimensions are in millimeters unless otherwise specified basic dimensions tolerance up to incl to incl to incl to incl above third angle projection name type no. issue revisions date material finish scale ceramic business unit, lcr device company matsushita electronic components co.,ltd. kadoma, osaka, japan draw check approval design drawing no. tolerance : +/-0.05 saw filter 5-0.38 5-0.44 2-0.735 0.075 0. 075 ( 1 ) (2) (3) (4) (5) ( 1 ) input (2) gnd ( 3 ) gn d ( 4 ) output (5) gnd 0.8 +/- 0. 1 5 note : the design manufacturing process, and specification of this device are subject to change without notice. under development 2.0 +/- 0. 1 5 1 .4 +/- 0. 1 5
(1) (2) (3) (4) (5) ceramic business unit , lcr device company matsushita electronic components co.,ltd. kadoma, osaka, japan do not scale drawing revisions indicated by all dimensions are in millimeters third angle projection unless otherwise specified basic dimensions tolerance up to incl to incl to incl to incl a bove issue revisions date material finish scale draw name type no. check a pproval design drawing no. s c d s : standard signal generator (output impedance 50 ohm) c : frequency counter d : detector (input impedance 50 ohm) saw filter fig. 2 s11 s22 0 level s c d s11 s22 123 4 5
do not scale drawing revisions indicated by ? all dimensions are in millimeters unless otherwise specified basic dimensions tolerance up to incl to incl to incl to incl above third angle projection name type no. issue revisions date material finish scale ceramic business unit, lcr device company matsushita electronic components co.,ltd. kadoma, osaka, japan draw check approval design drawing no. note : the design manufacturing process, and specification of this device are subject to change without notice. saw filter 0.735 0.810 5-0.480 r e c o m m e n d e d l a n d p a t t e r n 0.735 5-0.540 0.255 0.270 0.255
|
